SDS Max hammer drill bits are designed for compatible rotary hammers used in concrete and masonry drilling. Selecting the correct bit requires more than choosing a hole diameter. Shank compatibility, working length, overall length, cutting-head design, and the machine's drilling capacity all affect whether a bit suits the job.
Understanding these specifications helps buyers compare products accurately and avoid ordering a drill bit that fits the holder but cannot meet the application's requirements.
What Does SDS Max Mean?
SDS Max identifies the bit's connection system. It describes the interface between the accessory and the rotary hammer, rather than the diameter of the hole being drilled.
SDS Max drill bits have an 18 mm shank, while SDS Plus accessories use a smaller 10 mm shank. They do not fit directly into each other's tool holders. Always confirm the machine's specified accessory connection before purchasing.
The shank diameter and cutting diameter are separate measurements. An SDS Max drill bit with an 18 mm shank may have a cutting head considerably larger-or smaller-than that dimension.
How to Read SDS Max Drill Bit Dimensions
A product may display three dimensions, such as 18 × 200 × 340 mm. In a listing that specifies diameter, working length, and overall length in that order, the measurements mean:
|
Specification |
Example |
Meaning |
|
Cutting diameter |
18 mm |
Nominal diameter of the drilled hole |
|
Working length |
200 mm |
Specified usable drilling length |
|
Overall length |
340 mm |
Total length from cutting tip to shank end |
This exact combination appears in published product specifications. However, suppliers may present dimensions differently, so check the labeled technical fields rather than assuming the order.
Cutting Diameter: Match the Hole Requirement
The cutting diameter should match the project drawing or installation instructions. For anchor installation, select the specified drill diameter rather than choosing a nearby size.
Published SDS Max ranges include diameters such as 12, 16, 18, 22, 28, 32, and 40 mm, with larger options available in some product families. These examples do not define a universal size range: availability depends on the design and supplier.
Metric and imperial dimensions also require care. A nominal inch size should not automatically be treated as an exact substitute for a metric diameter, particularly when the hole forms part of an approved fastening system.
Working Length vs. Overall Length
Working length is the relevant dimension when checking drilling reach. Overall length includes the connection portion and should not be interpreted as achievable hole depth.
For example, a bit listed with a 400 mm working length may have a 520 mm or 540 mm overall length, depending on its design. Published specifications also show 340 mm overall-length bits with either 195 mm or 200 mm working lengths. Therefore, subtracting a fixed amount from overall length is unreliable.
Select sufficient working length for the required hole while considering access around the workpiece. Confirm depth-control arrangements separately, especially for blind holes.
Cutting-Head and Flute Specifications
SDS Max describes the connection, not a single cutting-head design. Products may use different carbide-head constructions and cutter arrangements.
Four-cutter carbide heads are documented for concrete and reinforced-concrete applications. Other ranges include four- or six-cutter configurations. These features should be evaluated against the stated base-material recommendation; cutter count alone does not establish drilling speed or service life.
Flute design is another comparison point because the drill must remove debris as the hole develops. For deeper drilling, follow the product's operating guidance rather than assuming that additional length alone makes the bit suitable.
Solid Drill Bits vs. Hollow Drill Bits
Conventional fluted bits and hollow extraction bits have different operating requirements. Hollow SDS Max drill bits connect to a suitable vacuum system to remove drilling dust through the bit.
Their specifications can include the required extraction equipment as well as diameter and working length. For anchor applications, confirm whether the exact bit-and-extraction arrangement is accepted by the installation instructions; do not assume it eliminates every additional cleaning step.
Check the Rotary Hammer Before Ordering
A matching shank confirms connection compatibility, but it does not establish that every SDS Max bit is appropriate for the machine. Check the rotary hammer's permitted drilling capacity and the bit's intended working mode.
Before ordering, record the connection type, cutting diameter, working length, overall length, base material, and head design. For extraction bits, add vacuum compatibility. Comparing these fields provides a clearer purchasing basis than relying on a product photograph or a shortened size description.
